www.supertalent.com The Official Super Talent Support Forum

Login
FAQ MembersRegister

Require permission to flash firmware for FTM64GX25H

The latest and final firmware for Ultra Drive GX/GX2 series.

Postby SSD-James » Wed Mar 14, 2012 10:04 am

OK, it is allowed.

Model: FTM64GX25H
Serial: R554513-AIBX-614A001
SSD-James
 
Posts: 2076
Joined: Fri Jul 16, 2010 12:41 pm

Postby GetCool » Wed Mar 14, 2012 11:37 am

Thanks.

My drive had no switch inside of it either. It just had two holes through the PCB labeled "J2" and "FACTORYMODE". Seems like there should be a header there for a jumper, or something.

I had to remove the PCB from the case entirely, short the two pinholes using a strand of wire, then run MP TOOL with it wired up like that. It worked, although it was a bit nerve-wracking flashing my SSD as a bare PCB hanging out of my PC case by SATA cables.

All in all, the procedure worked just fine. I used the Auto-Detect feature. Oh, and I'm running an Intel chipset by the way.
GetCool
 
Posts: 3
Joined: Mon Jul 06, 2009 5:26 pm

Postby SSD-James » Wed Mar 14, 2012 1:43 pm

Thanks for your feedback.
That was why I made a guide for jumpering for PCB.
You may not need that much of hard works to do that.
If you used paper clip as I drawed on the guide, it was much easier.
You did not need to open the bottom casing.
Anyway, good to hear you made it.

Thanks,
James
SSD-James
 
Posts: 2076
Joined: Fri Jul 16, 2010 12:41 pm

Postby GetCool » Thu Mar 15, 2012 9:07 am

SSD-James wrote:That was why I made a guide for jumpering for PCB.
You may not need that much of hard works to do that.
If you used paper clip as I drawed on the guide, it was much easier.


James, can you please provide a link to this guide? I searched the forums for a long time yesterday before figuring out that I needed to short J2 in order to access FACTORYMODE, and I did not find any guides or pictures showing how to do this.

For the record, I did attempt to use a paperclip first. The first paperclip was too thick and would not fit through the holes. The second paperclip was too thin and would not stay on.

Jumper wires, made for PCB modding, were much better for the job. I had to borrow some from a friend who is an engineer and designs PCBs. They clipped right into the holes easily, and it was actually easier to access by removing both the top and bottom covers.
GetCool
 
Posts: 3
Joined: Mon Jul 06, 2009 5:26 pm

Postby SSD-James » Thu Mar 15, 2012 10:16 am

Her it is:
viewtopic.php?f=74&t=10867
Need to download the 1st file.
SSD-James
 
Posts: 2076
Joined: Fri Jul 16, 2010 12:41 pm

Postby Videoman79 » Fri Mar 23, 2012 3:01 pm

Model: FTM64GX25H
Serial: P590946-ATBX-9259061
Current FW: 1916
Videoman79
 
Posts: 4
Joined: Sat Feb 20, 2010 7:08 am

Postby SSD-James » Mon Mar 26, 2012 8:28 am

Model: FTM64GX25H
Serial: P590946-ATBX-9259061
Current FW: 1916

Your SSD Flash selection is TH58NVG5D1DTG20 64GB. or K9LBG08U0M 64GB.
Try the first one and if it works, do not try the 2nd one.
If 1st one is not working, try 2nd one.
Thanks,
James
SSD-James
 
Posts: 2076
Joined: Fri Jul 16, 2010 12:41 pm

Postby cell21633 » Sun Apr 08, 2012 9:23 pm

FTM64GX25H
P576465-BDBX-8059246
cell21633
 
Posts: 1
Joined: Sun Apr 08, 2012 9:19 pm

Postby SSD-James » Mon Apr 09, 2012 10:03 am

FTM64GX25H
P576465-BDBX-8059246
Your SSD Flash selection is K9LBG08U0M 64GB.
You have permission to open the case to update the firmware.
SSD-James
 
Posts: 2076
Joined: Fri Jul 16, 2010 12:41 pm

Postby boskameel » Thu Apr 12, 2012 1:53 pm

FTM64GX25H
P601148-AFBX-C099124
auto detection

Has switch but flashing just fails, drive shows up as YATAPONG barefoot rom

advice?

thanks
boskameel
 
Posts: 2
Joined: Thu Apr 12, 2012 1:10 pm

PreviousNext

Return to Latest Firmware MP TOOL Download

Who is online

Users browsing this forum: No registered users and 2 guests